Zircon Stud Sensor 50 is an electronic stud finder with a variety of amazing features. You can also use it professionally because it is an accurate and precise electronic stud finder. It is also a famous electronic stud sensor that is used widely and sold exclusively on Amazon.
It is also easy to handle because of its ergonomic design. You can rotate your hands very easily while holding it. The place where you hold it has a rubber molded grip which ensures a secure grasp.
|Weight: 7 ounces
Dimensions: 8.5 x 4 x 2 inches
Batteries Included?: No
Batteries Required?: Yes
|Check On Amazon|
Similar to Vivreal Stud Finder the Zircon stud sensor e50 is the accurate stud sensor which can locate the wood studs and metal stud which would be deep enough. You can easily find the studs whether they are in the walls, ceilings, or floors.
So you can save a lot of your time by finding the studs with electronic stud sensor e50.
Table of Contents
- It is an amazing electronic stud finder.
- This stud finder can easily detect the edges of wood studs and metal studs up to 1.5 inches deep.
- The stud finder has a beautiful design and has an ergonomic grip so that you can handle it easily for any size and at any angle.
- A 9V battery is required but is not included in the packaging.
- This 9v battery is very helpful to run the electronic stud sensor at optimal performance.
- You can easily find studs with the help of electronic stud sensor e50.
- You can also detect the presence of live unshielded electrical wires with the help of wire warning detection technology.
- It also has stud scan mode and deep scan mode with the help of which you can detect the stud precisely and accurately.
- When you become successful in finding the studs then it has patented over the stud indicator which indicates you about the stud.
- Zircon stud sensor e50 has a spotlight pointing system that ensures 100% precise and accurate results.
- The scanning depth doubles with the help of deep scan mode which can detect up to 1 and a half inches deep.
- It indicates the stud edge with the help of easy-to-read LCD.
|Dimensions:||1.65 x 2.87 x 6.77 inches|
|Item Weight:||7 ounces|
The Zircon e50 has two modes. You can use these modes according to your choice and need. Both modes works perfectly fine.
You can find the wood studs or metal studs which are almost ¾ inches deep with the help of this amazing stud finder. So when you are looking for a wood stud or metal stud then you have to select this mode. You will find the indication of the stud when the indicator flashes.
If you find that the studs finder is giving you irregular reading or the signal strength indicator is weak then it means the studs might be behind more than ¾ inches of the drywall.
Then it is the time to select the deep scan mode which doubles the scanning depth to one and a half inches deep. Now, you will find the studs with increased accuracy and precision.
We all know that wire warning detection works in deep scan mode as well as a stud scan mode by the indicator which flashes when you detect the live or unshielded wire.
Wire warning detection:
As I have discussed earlier, wire warning detection works in all modes. This is because the manufacturers are concerned about your safety. With wire warning detection technology, you can find the live and unshielded electrical wiring up to 2 inches deep.
We can use a zircon stud Finder for various purposes such as mounting a TV or installing cabinets.
We can also use it for some new garage shelving.
When you don’t know where to hang your TV or make the new garage shelving then this Zircon stud find e50 is very helpful in finding you both the edges of the studs as well as a center of the studs behind your walls.
First of all, you have to install the new 9-volt battery by matching the positive and negative terminals. Then make it on by pressing the power button for some time.
In the next step, you have to select the mode whether it is stud scan mode or deep scan mode. Now, place it on the wall where you have to find the stud.
When the spotlight pointer shines then it means that you have to find the stud. Then keep the scanning process behind the marked spot until you get the right spot.
For using the zircon stud finder e50, you have to use the fully charged 9v battery. When you purchase this stud sensor, you will also get the manual instructions so that if you have any problem regarding the operation of this stud sensor then this manual will help you a lot.
In this manual, you will get the information about how to install the battery, how to select the mode, how to find a stud, etc.
You will also get the information about the wire warning detection of the stud sensor e50.
There are many operating tips in this manual which will help you to use the stud sensor accurately and professionally.
The wire warning detection alerts you about the presence of live AC wires. So be aware of it.
Yes, e50 Zircon required a batter to start work. Zircon stud sensor e50 is also a multi scanner that requires a new alkaline 9-volt battery.
This battery comes with an extended expiration date so that it can perform the proper operation.
Make sure that the battery which you are purchasing for your zircon stud sensor is according to requirement. If you have any problem purchasing a 9-volt battery then you can get the instructions for it.
The main difference between zircon stud sensor E50 and zircon stud sensor HD 55 is that it does not require any battery and this battery is also not included in the packaging.
Zircon e50 can detect the metal studs up to 1.5 inches deep. zircon HD 558 can detect the metal studs up to 3 inches deep.
There is a V groove in zircon stud sensor HD 55 but in zircon multi scanner e50, there is no groove. This group allows the stud sensor to pinpoint the studs with accuracy.
In Zircon e50 you can find the stud very easily by projecting a beam of light so that you can visualize the stud location. All this can be possible with spotlight beam Technology.
Zircon stud sensor e50 is the best choice when you are finding the studs. There are two options whether you have to purchase the electronic stud sensor or magnetic stud sensor.
But from my point of view, the electronic stud sensor is the accurate one, and fortunately, the e50 is also an electronic stud sensor.
You can use this in homes as well as different DIY skills. So, it is a professional and accurate stud sensor that can identify the wires or other foreign objects.
Zircon stud sensor if 50 is an electronic stud sensor that can detect the presence of metal studs or wood studs as well as the live AC wire.
Now you will get accurate results at a reasonable price with this electronic wall scanner.
It has an easy-to-read display that pinpoints the exact location of the studs as well as the edges of the studs.
Q 1: Will I have to replace a new 9V battery every time if I have used it for a month?
Ans: If you are using zircon e50 for a month and thinking of replacing the new 9V battery then you do not need to if it has been sitting for a month.
But keep this thing in mind that if you are not using the stud finder regularly then you do not have to leave the battery in your tool as there is a chance of corrosion of the battery.
There is also another way to save your battery by putting it in an upside-down position if you are not using it.
Q 2: Is this stud sensor work by changing in the density or by detecting the metal?
Ans: Yes, the stud sensor e50 works by changing the density in the drywall. However, this electronic stud finder can also find the metal studs by changing in the density not because they are metal. The density changes when it shows the edges and center of the stud.
Q 3: Is the stud sensor e50 find the stud behind the stucco walls?
Ans: In general, Zircon stud sensor e50 is not designed for use outdoors. If you want to find the wire mesh and varying insulation material in outdoor stucco construction then, unfortunately, it will not be fine.
This stud sensor has electrical depth scanning technology but it is unusable. If you are identifying the wall studs from the interior side of the wall, you should use a window or a door to measure the distances and then transfer these measurements to the exterior sides.
Q 4: Can the Zircon stud sensor e50 can detect the stud for wiring beneath the old plaster walls?
Ans: No, the stud finder will not find the studs behind the plaster or lath as it is not designed for finding the studs behind the plaster wall. So, we will not recommend you to find the wood stud or metal stud behind the Plaster walls or lath. For this purpose, we have to use a metal scanner.
Q 5: Can I use this stud sensor to locate the joists in the ceiling? If the ceiling, drywall, or sheetrock which is not so smooth?
Ans: Yes, the stud finder e50 can find the stud on the ceiling which is drywall or sheetrock. If we talk about the texture of the wall, then you can find the stud by using a thin piece of cardboard to scan through which will smooth out the surface for you.
You cannot deny the importance of zircon e50 as you can use it in your home for home renovations and can also use professionally in different outdoor construction sites.
The good thing about this stud sensor is that it is easy to handle and easy to use. It works effectively in a stud scan and deep scan mode.
It also has safety features that alert you about the presence of live and unshielded electrical AC wires. So it is a perfect tool which meets your needs and gives you accurate and precise results.